Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 149

Страница: 149 / 175

If the No battery alarm is generated, after you turn on the battery switches, the

alarm is cleared automatically within 2 minutes.

Step 14 Check that no alarm is generated for any UPS, and start the new UPS in inverter

mode. The parallel system transfers to inverter mode. View the system running

diagram to check that the system is working in inverter mode.

----End

8.7 Commissioning a Dual-Bus System

Context

The dual-bus system consists of one master and one slave BSC system. You can

specify one master and one slave BSC system (UPSs in the same system cannot be

set to both master and slave BSC systems) during initial startup, and change the

settings under the guidance of maintenance engineers when needed. Set the BSC

master and slave systems to master and slave modes respectively.

Procedure

Step 1 Connect BSC cables.

Figure 8-2 Parallel cable connections in a dual-bus parallel system

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

8 Parallel System Commissioning

Issue 02 (2021-04-22)

141

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды