Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 28

Страница: 28 / 158

UPS2000-G-(3 kVA-20 kVA)-V2
User Manual (Two Live Wires)

2 Quick Introduction

Issue 07 (2019-12-19)

2.4 Optional Components



UPS2000-G-3 kVA cannot support parallel system.



For UPS2000-G-10 kVA/15 kVA/20 kVA, if the AC input and AC output uses two live
wires, PDC-0038V4ACIOA, PDC-0091V2ACIOA, and PDC-0038V4ACIOA-V2 cannot
be used.

Table 2-2

Optional components

Component Model

Function

Remarks

Parallel cable

DB15M, CC8P0.48B(S),
DB15F

Connect UPSs in
parallel for
UPS2000-G-6 kVA/10
kVA/15 kVA/20 kVA.

A parallel cable
is 1.5 meters
long.

Battery
temperature
sensor

TE820E10B/W103-B02-L1

Measures the ambient
temperature of the
external power module
and battery pack.

The temperature
ranges from
–40ºC to +80ºC.

The standard
cable is 2 meters
long. To
increase the
length, install a
magnetic ring at
the sensor plug.

Ambient
temperature
and humidity
sensor

WS302M2A-5

ENR1DETA MODULE

Measures the UPS
ambient temperature
and humidity.

The ambient
temperature
ranges from
0–50º

C. The

ambient
humidity ranges
from to
0%–100% RH.
It is used
together with a
Simple Network
Management
Protocol
(SNMP) card.

SNMP card

RMS-SNMP01A

Monitors the UPS and
the ambient
temperatures and
humidity (if required)
and allows for Ethernet
networking.

N/A

6 kVA output
isolation

DGL-6/0.22

Provides isolation
solutions for customer

The output
isolation

Содержание UPS2000-G-10KRTLV2































































































































































Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы:

Huawei UPS2000-G-10KRTLV2, Руководство пользователя, Страница: 28 / 158

Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы: