Huawei UPS2000-G-10KRTLV2 Скачать руководство пользователя страница 108

Страница: 108 / 158

UPS2000-G-(3 kVA-20 kVA)-V2
User Manual (Two Live Wires)

9 Technical Specifications

Issue 07 (2019-12-19)

101

Item

3 kVA

6 kVA

10 kVA

15 kVA

20 kVA

Dynamic voltage
tolerance

±5%

Output voltage
unbalance

N/A



±1% (balanced load)



±3% (unbalanced
load)

Average
frequency
tracking rate

0.5–2 Hz/s (single UPS) or 0.5–1 Hz/s (parallel system)

Power segment
(only in single
UPS mode)



If overloaded, the UPS disconnects from secondary loads and
checks whether it is still overloaded.



In battery mode, the UPS disconnects from secondary loads if the
battery voltage is less than the specified value.



In battery mode, the UPS disconnects from secondary loads if the
discharge time is more than the specified value.

9.6 Battery Specifications

Table 9-6

Battery specifications

Item

3 kVA

6 kVA

10 kVA

15 kVA

20 kVA

Rated battery
voltage

240 V DC

±240 V DC

Number of
batteries

16–20, each 12 V DC. If the smaller
value between the numbers of batteries,

, is less than 20, the battery power is

derated to

/20.

16–20, respectively in the
positive and negative battery
strings. The rated number is
20. If the smaller value
between the numbers of
batteries in the positive and
negative battery strings,

, is

less than 20, the battery
power is derated to

/20.

Battery string
sharing in a
parallel system

Disabled

Enabled

Leakage current

≤ 500 μA

Depth of
discharge (DOD)
protection

The discharge time exceeds 16 hours (configurable on the LCD).

The single-battery voltage drops below 10.8 V in normal mode.

Backup time

> 4 minutes (at full rated load),

show the battery pack backup time.

Содержание UPS2000-G-10KRTLV2































































































































































Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы:

Huawei UPS2000-G-10KRTLV2, Руководство пользователя, Страница: 108 / 158

Результаты поиска

Содержание UPS2000-G-10KRTLV2

Отзывы: