Huawei Telecom Power TP48200A-HT19C3 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 99

background image

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

3 Components

Issue 03 (2019-11-15)

Copyright © Huawei Technologies Co., Ltd.

35

Function

Working Principle

circulation heat sink and returns to the external environment through the air exhaust
vents on the external circulation heat sink. The heat exchange between the internal and
external environment is implemented so far.

Heating

The TCUA control box controls the refrigeration chip in the TEC module to heat the
internal circulating air. The internal circulation fan draws the air inside the battery
compartment into the internal circulation heat sink. The internal circulation heat sink
heats the air and then returns the heated air to the battery compartment through the air
exhaust vents. Meantime, the external circulation fan operates according to control logic
and draws natural air into the external circulation heat sink. The air gives out heat and
returns to the external environment through the air exhaust vents on the external
circulation heat sink.

Figure 3-15

TEC airflow directions

3.7 Sensor

Figure 3-16 shows the positions of all sensors in the TP48200A-HT19C3 & HT19C4.

«
...
40
41
42
43
44
...
»

Содержание Telecom Power TP48200A-HT19C3




































































































Отзывы:

Нет отзывов

Похожие инструкции для Telecom Power TP48200A-HT19C3

Бренд: KAKA Industrial Страницы: 10

Бренд: Gearwrench Страницы: 3

FrameSaver 9620

Бренд: Paradyne Страницы: 4

Бренд: Makita Страницы: 17

Бренд: Fein Страницы: 148

Бренд: Fein Страницы: 41

Бренд: Parkside Страницы: 132

Бренд: SilverStone Страницы: 12

X 18 V - MANUEL 3

Бренд: Parkside Страницы: 12

Бренд: Kolver Страницы: 7

Бренд: New Trent Страницы: 2

Toolson PRO-OF 1255

Бренд: EINHELL Страницы: 268

M18 FORCELOGIC HCCT109/42

Бренд: Milwaukee Страницы: 8

Бренд: Yokota Страницы: 8

Бренд: Rotec Страницы: 21

Бренд: Somogyi Страницы: 16

Бренд: Parkside Страницы: 54

Бренд: unicraft Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды