Huawei SUN2000-4.95KTL-JPL0 Скачать руководство пользователя страница 58

Страница: 58 / 65

SUN2000-4.95KTL-JPL0
User Manual

8 Handling a Solar Inverter

Issue 03 (2020-06-03)

Handling a Solar Inverter

8.1 Removing a Solar Inverter

Procedure

Step 1

Power off the system.

Step 2

Disconnect all cables from the solar inverter, including the signal cable, DC input power
cables, AC output power cable, and PE cable.

Step 3

Remove the solar inverter from the mounting bracket.

Step 4

Remove the mounting bracket.

----End

8.2 Packing a Solar Inverter



If the original packaging is available, put the solar inverter inside it and then seal it using
adhesive tape.



If the original packaging is unavailable, put the solar inverter inside a suitable hard
carton and seal it properly.

8.3 Disposing of a Solar Inverter

If the solar inverter service life expires, dispose of it according to the local disposal rules for
electrical equipment and electronic component waste.

Содержание SUN2000-4.95KTL-JPL0


































































Результаты поиска

Содержание SUN2000-4.95KTL-JPL0

Отзывы:

Похожие инструкции для SUN2000-4.95KTL-JPL0

Бренды по названию

Популярные бренды

Huawei SUN2000-4.95KTL-JPL0, Руководство пользователя

Результаты поиска

Содержание SUN2000-4.95KTL-JPL0

Отзывы:

Похожие инструкции для SUN2000-4.95KTL-JPL0

Бренды по названию

Популярные бренды