manualshive.com logo in svg

Huawei SmartLi 2.0, Руководство пользователя, Страница: 48 / 173

Поделиться
Скачать
Huawei SmartLi 2.0 Скачать руководство пользователя страница 48

4

 Installation

4.1 Installation Preparations

4.1.1 Site

4.1.1.1 Installation Environment

●

Do not install the SmartLi in high temperature, low temperature, or damp

environments.

●

Install the SmartLi away from water sources, heat sources, and flammable or

explosive materials.

●

Keep the SmartLi away from direct sunlight, dust, volatile gases, corrosive

materials, and air dense with salt particles.

●

Do not install the SmartLi in environments with conductive metal scraps in

the air.

4.1.1.2 Installation Clearances

Reserve the following clearances around the cabinet to facilitate operations and

ventilation:
●

Reserve at least 800 mm from the front of the cabinet.

●

Reserve at least 500 mm from the top of the cabinet.

●

The SmartLi can be installed against a wall and no space needs to be reserved

at the rear.

SmartLi 2.0

User Manual

4 Installation

Issue 09 (2022-01-30)

Copyright © Huawei Technologies Co., Ltd.

38

Содержание SmartLi 2.0














































































































































































Отзывы:

Нет отзывов