Huawei SmartLi 2.0 Скачать руководство пользователя страница 152

Страница: 152 / 173

Figure 9-5 Uploading and activating the software (the BCB of a single battery

cabinet is OFF)

NO TE

1. The method for uploading and activating the software when the BCBs of all battery

cabinets in a parallel system are ON or OFF is the same as the method for uploading

and activating the software when the BCB of a single battery cabinet is OFF.

2. The system starts the upgrade process. If the BCBs of all battery cabinets are OFF before

the start, the MDU and all the battery cabinets are upgraded concurrently. If the BCBs of

all battery cabinets are ON before the start, the MDU and the battery cabinets (battery

cabinet 1, battery cabinet 2, ..., and battery cabinet

) are upgraded one by one. The

upgrade progress is displayed in the Status column. During the upgrade of the MDU,

the message "The MDU will restart to complete the upgrade process. Log in again after

2 minutes." is displayed. Tap OK. The MDU restarts to complete the upgrade task. After

about 2 minutes, the default screen is displayed. Choose System Status > Maintenance

and log in on the LCD again.

9.6 Replacing a Fire Extinguisher Cylinder (Without a

Lithium Battery Side Cabinet)

Prerequisites

●

Tools: insulated socket wrench, insulation gloves, Phillips screwdriver, key to

the cabinet door, torque wrench, pipe cutter, and pipe holder

●

Materials:
–

Check the fire extinguisher cylinder and all components for any damage,

abrasion, or corrosion. If there is any visible abrasion or corrosion, replace

the damaged components and all corroded components.

–

Check that the valve is closed (vertical to the cylinder).

–

Recommended extinguishant: heptafluoropropane or perfluorohexanone

SmartLi 2.0

User Manual

9 Parts Replacement

Issue 09 (2022-01-30)

142

Содержание SmartLi 2.0














































































































































































Результаты поиска

Содержание SmartLi 2.0

Отзывы:

Huawei SmartLi 2.0, Руководство пользователя, Страница: 152 / 173

Результаты поиска

Содержание SmartLi 2.0

Отзывы: