Huawei SmartLi 2.0 Скачать руководство пользователя страница 147

Страница: 147 / 173

Step 9 Reinstall the BCU and turn on the ready switch.

Step 10 Press and hold the POWER ON/OFF button on the BCU for more than 2s. The

green indicator of the BCU blinks at 4 Hz.

NO TICE

If the Version incompatible alarm is generated, you need to upgrade the version

before switching on the battery circuit breaker.

Step 11 After the green indicator of the BCU blinks at 10 Hz and the red indicator is steady

on, switch on the battery circuit breaker on the SmartLi.

----End

9.4 Replacing a SmartLi Fuse

Prerequisites

●

Tools: insulated socket wrench, insulation gloves, Phillips screwdriver, key to

the cabinet door

●

Material: a new fuse

Procedure

Step 1 Open the front door of the cabinet and switch off the battery circuit breaker. Press

and hold the POWER ON/OFF button on the BCU for more than 5s to power off

the cabinet.

Step 2 Turn off the ready switch on the BCU, remove the bolts that secure the BCU, and

pull it out for about 10 cm.

Step 3 Remove the fuse cover.
Step 4 Remove the screws that secure the fuse and replace the faulty fuse with a new

one.

SmartLi 2.0

User Manual

9 Parts Replacement

Issue 09 (2022-01-30)

137

Содержание SmartLi 2.0














































































































































































Результаты поиска

Содержание SmartLi 2.0

Отзывы:

Huawei SmartLi 2.0, Руководство пользователя, Страница: 147 / 173

Результаты поиска

Содержание SmartLi 2.0

Отзывы: