Huawei SmartLi 2.0 Скачать руководство пользователя страница 143

Страница: 143 / 173

Troubleshooting

CA UTION

Do not clear alarms by reinstalling modules.

Table 8-1 Troubleshooting

Case

Symptom

Possible Cause

Measure

Battery

module

abnormal

The indicator of

the battery

module is red or

off.

The battery module is

faulty.

Replace the battery

module.

The communications

cable to the battery

module is not

connected.

Reconnect the

communications

cable.

BCU

abnormal

The indicator is

yellow or red.

The battery cabinet

generates a minor

alarm.

Handle the alarm

according to the

alarm reference.

The battery cabinet

generates a critical

alarm.

NO TE

For details about component replacement and maintenance involved in Troubleshooting

and Alarm List, consult technical support.

SmartLi 2.0

User Manual

8 Troubleshooting

Issue 09 (2022-01-30)

133

Содержание SmartLi 2.0














































































































































































Результаты поиска

Содержание SmartLi 2.0

Отзывы:

Huawei SmartLi 2.0, Руководство пользователя, Страница: 143 / 173

Результаты поиска

Содержание SmartLi 2.0

Отзывы: