Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 77 / 553

background image

l

Configure a VDSL2 alarm template.
1.

Run the

vdsl alarm-profile quickadd

command to quickly add a VDSL2 line alarm

profile, or run the

vdsl alarm-profile add

command to interactively add a VDSL2

line alarm profile.

2.

Run the

vdsl channel-alarm-profile quickadd

command to quickly add a VDSL2

channel alarm profile, or run the

vdsl channel-alarm-profile add

command to

interactively add a VDSL2 channel alarm profile.

3.

Run the

vdsl alarm-template quickadd

command to quickly add a VDSL2 alarm

template, or run the

vdsl alarm-template add

command to interactively add a VDSL2

alarm template.

A VDSL2 alarm template consists of a VDSL2 line alarm profile and a VDSL2
channel alarm profile. Bind a VDSL2 alarm template rather than a VDSL2 line alarm
profile or a VDSL2 channel alarm profile to a VDSL port.

----End

Example

Assume the following configurations:

l

Path mode: PTM mode

l

Downstream minimum reserved rate: 4096 kbit/s

l

Channel mode: interleave mode

l

Downstream maximum interleave delay: 8 ms

l

Upstream minimum interleave delay: 2 ms

l

SNR margin: 6 dB

l

Downstream minimum INP: 4

l

Upstream minimum INP: 2

To add VDSL2 profiles with index 3, do as follows:

huawei(config)#

vdsl service-profile 3 quickadd path-mode ptm bearer1-rate 512

4096 8192 128 128 128 100000 128

huawei(config)#

vdsl delay-inp-profile quickadd 3 bearer1-interleaved-delay 8 2

bearer1-inp 4 2

huawei(config)#

vdsl noise-margin-profile quickadd 3 snr-margin 60 0 100 60 0

100

3.8 Configuring the System Clock

This topic describes how to configure the system clock to restrict the clock frequency and phase
of each node on a network within the preset tolerance scope. This prevents the deterioration of
the TDM service quality caused by inaccurate signal timing at both the transmit and receive ends
in the digital transmission system.

Context

l

The IP-based development is the trend of future network and service development.
Currently, certain difficulties exist in the transition of the access network (AN) from the
traditional network to the IP-based Ethernet bearer network. One of the difficulties is how
to carry the traditional TDM service on the IP network.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

66

«
...
75
76
77
78
79
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Express Ethernetwork DI-704P

Бренд: D-Link Страницы: 17

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: TC Electronic Страницы: 55

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 5

Бренд: Supermicro Страницы: 16

Бренд: Paradyne Страницы: 10

Бренд: Macsense Страницы: 13

Бренд: u-blox Страницы: 29

Бренд: NKE Страницы: 15

DiamondLink 3201

Бренд: Patton Страницы: 12

Ezi-SERVOII EtherCAT TO

Бренд: Fastech Страницы: 108

Бренд: Global411 Страницы: 15

Бренд: Tripp Lite Страницы: 3

Бренд: Hi-flying Страницы: 59

Бренд: Freescale Semiconductor Страницы: 124

Бренд: nox Страницы: 16

Бренд: Avaya Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды