Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 59 / 553

background image

–

Run the

undo broad-service power-off shutdown

command to enable disabled

bandwidth services.

----End

Example

To manually power off an ASRB board that is not used and in slot 0/4 of an MA5616 to reduce
energy consumption, do as follows:

huawei(config)#

board power-off 0/4

Powering off the board will interrupt the running services.
Are you sure to power off the board?(y/n)[n]

y

The board is powered off successfully
huawei(config)#

display board 0

-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1 Online/Offline
-------------------------------------------------------------------------
0 H831CCUB Active_normal GP1A ASDA
1 H838ASPB Normal
Online
2 H835ADLE Normal
Online
3
4 H838ASRB

Shutdown(manual)

Online

5 H831PAIA Normal
-------------------------------------------------------------------------

3.4 Configuring the Link Aggregation of Upstream Ethernet
Port

Port aggregation means aggregating the two upstream GE ports of the MA5616 to increase the
bandwidth through load balancing. When a certain aggregated GE port or GE link fails, data is
transmitted through another GE port. Thus, the reliability of the transmission is enhanced.

Prerequisites

l

The network device and the line must be normal.

l

The VLAN of the interface on the upper-layer device of the MA5616 must be consistent
with the VLAN configured for the upstream port on the MA5616.

Context

l

The parameters configured for two aggregation ports need to be the same.

l

No static MAC address is allowed on the aggregation ports. You can run the

display mac-

address

command to query the configuration.

l

The ports to be aggregated cannot be destination mirroring ports.

Procedure

Step 1

Configure the Ethernet port aggregation.

Run the

link-aggregation

command to configure the Ethernet port aggregation.

Step 2

Query the information about the aggregation group.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

48

«
...
57
58
59
60
61
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Ubiquiti Страницы: 50

Бренд: Winext Страницы: 37

Бренд: Watchguard Страницы: 40

Бренд: NETGEAR Страницы: 84

Бренд: Paradyne Страницы: 23

Vigor 2760 Series

Бренд: Draytek Страницы: 54

Бренд: Tandy Страницы: 24

Бренд: Atmel Страницы: 2

Бренд: Tripp Lite Страницы: 3

Бренд: Alcatel-Lucent Страницы: 60

Бренд: ADTRAN Страницы: 4

Developer's Board

Бренд: Sony Ericsson Страницы: 28

Data Capture Board CLC-CAPT-PCASM

Бренд: National Semiconductor Страницы: 15

Бренд: NetCommWireless Страницы: 28

Бренд: ADTRAN Страницы: 136

Бренд: Sharedband Страницы: 3

Бренд: Intel Страницы: 51

Бренд: IBM Страницы: 168

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды