Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 485 / 553

background image

quit
save

9.5.3 Configuration Example of the Triple Play Service - Multiple
PVCs for Multiple Services

This topic describes how to configure the triple play service in the multi-PVC for multiple
services mode.

Prerequisites

Before configuring the triple play service, make sure that:

l

The network devices and lines are in the normal state.

l

The CPE is already configured (the CPE supports different PVCs for different services).

l

All boards of the device run in the normal state.

l

The VDSL2 line template and alarm template that are bound to the port are already
configured. For details on the configuration procedure, see

3.7.3 Configuring the VDSL2

Service Requirements

l

The MA5616 is used on the GE upstream transmission network.

l

VDSL2 user 1 and VDSL2 user 2 are connected to the MA5616 to implement the triple
play.

l

The Internet service is provided in the PPPoE mode.

l

After receiving different traffic streams, the MA5616 provides different QoS guarantees
to the traffic streams according to the traffic priorities in the PVC.

Networking

Figure 9-16

shows the example network of the triple play service in the multi-PVC for multiple

services mode.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

474

«
...
483
484
485
486
487
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Laird Страницы: 36

Бренд: Ubiquiti Страницы: 50

Бренд: Maxim Страницы: 26

Бренд: NetComm Страницы: 3

RouterBOARD Groove

Бренд: MikroTik Страницы: 4

Бренд: Intellinet Страницы: 2

Бренд: Magnadyne Страницы: 8

IPAM-1600s Series

Бренд: C-Com Страницы: 148

Бренд: Idis Страницы: 85

Бренд: Selta Страницы: 83

Бренд: Billion Страницы: 120

Бренд: Freescale Semiconductor Страницы: 8

NVRx-7300 series

Бренд: Swann Страницы: 9

PFC Chokes PFC3515V Series

Бренд: Delta Electronics Страницы: 1

SFD-2 MkIII Jumper

Бренд: Anthem Audio Страницы: 2

Бренд: netsys Страницы: 164

Бренд: Spirent Страницы: 22

Бренд: Paradyne Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды