Huawei SmartAX MA5616 Скачать руководство пользователя

Страница: 453 / 553

mg-ringmode add 0 0 4

Configure the TID template of the PSTN user on the MG interface.

tid-format pstn prefix huawei template 6

An MG interface must be started manually and the configuration file cannot be imported directly.

reset coldstart

Query the running status of the MG interface.

quit
display if-h248 all

Confirm the service board.

board confirm 0/3

Configure the PSTN user data.

esl user
mgpstnuser batadd 0/3/0 0/3/31 0

Configure the local digitmap.

quit
local-digitmap add huawei normal ([2-8]xxxxxxx|[2-8]xxSxxxxxxx|13xxxxxxxxx|
0xxxxxxxxx)

Configure the polarity reversal charging function.

pstnport
pstnport attribute batset 0/3/0 0/3/31 reverse-pole-pulse enable

Save the data.

quit
save

9.3.2 Configuration Example of the VoIP PSTN Service (Based on
the SIP Protocol)

This topic describes how to configure the VoIP PSTN service based on the SIP protocol.

Prerequisites

The voice service board ASRB must be installed in the specified slot.

The SIP interface must be configured. For how to configure the SIP interface, see

7.2.1

Configuring the SIP Interface

The PSTN user data corresponding to the SIP interface must be configured on the IMS.

Networking

Figure 9-8

shows the example network of the VoIP PSTN service based on the SIP protocol.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

442

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды

Huawei SmartAX MA5616, Руководство по настройке

Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды