Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 45 / 553

background image

NOTE

l

The IP address is the management IP address of the MA5616.

l

Select the SNMP parameters based on the selected SNMP protocol. This section
considers the SNMP V1 default profile as an example. You can select the profile
according to the plan.

c.

Click

OK

. Several seconds to some 10 minutes are required for uploading the

device data. After reading the related data, the system automatically updates the
device icon.

----End

Result

You can maintain and manage the MA5616 through the U2000.

Configuration File

The following part provides the script for configuring the outband NMS (on the device).

snmp-agent community read public
snmp-agent community write private
snmp-agent sys-info contact HW-075528780808
snmp-agent sys-info location Shenzhen_China
snmp-agent sys-info version v1
snmp-agent trap enable standard
snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC
snmp-agent target-host trap-paramsname ABC v1 securityname private
snmp-agent trap source meth 0
save

The following part provides the script for configuring the inband NMS (on the device). The
management VLAN ID of the upstream port is 30.

snmp-agent community read public
snmp-agent community write private
snmp-agent sys-info contact HW-075528780808
snmp-agent sys-info location Shenzhen_China
snmp-agent sys-info version v1
snmp-agent trap enable standard
snmp-agent target-host trap-hostname huawei address 10.10.1.10 trap-paramsname ABC
snmp-agent target-host trap-paramsname ABC v1 securityname private
snmp-agent trap source vlanif 30
save

3.2.2 Configuring the U2000 (Based on SNMPv2c)

When SNMPv2c is used, the MA5616 can be interconnected with the U2000 in inband or
outband networking mode.

Prerequisites

l

If the device is interconnected with the NMS in outband networking mode, the
communication port (maintenance network port) must be configured. For detailed
procedure, see

3.1.2 Configuring Outband Management

l

If the device is interconnected with the NMS through the PON upstream port in inband
networking mode, the communication port (PON upstream port) must be configured. For
detailed procedure, see

3.1.3 Configuring Inband Management (GPON Upstream)

.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

34

«
...
43
44
45
46
47
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

Бренд: A10 Страницы: 52

Бренд: Harmonic Страницы: 56

Бренд: SeaLevel Страницы: 17

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

Бренд: ZyXEL Communications Страницы: 5

RocketCache 3240X8

Бренд: HighPoint Страницы: 17

Бренд: Quantum Страницы: 7

AT32F421 Series

Бренд: ARTERY Страницы: 337

Бренд: Intel Страницы: 958

Бренд: PairGain Страницы: 80

Бренд: RTS Страницы: 3

Бренд: VideoWave Страницы: 12

Бренд: Telestar Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды