Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 441 / 553

background image

Configure the multicast uplink port, multicast programs, and multicast users.

igmp uplink-port 0/0/1
multicast-vlan 4002
igmp uplink-port 0/0/1
igmp program add name program1 ip 224.1.1.1 sourceip 10.10.10.10
multicast-vlan 4003
igmp program add name program2 ip 224.1.1.2 sourceip 10.10.10.11
btv
igmp user add service-port 100
igmp user add service-port 101
multicast-vlan 4002
igmp multicast-vlan member service-port 100
multicast-vlan 4003
igmp multicast-vlan member service-port 101
quit
save

9.2.2 Configuration Example of the Multicast Video Service
(Dynamic Generation Mode)

This topic describes how to configure the multicast video service if the program matching mode
of the multicast VLAN is the dynamic generation mode.

Prerequisites

l

Network devices and lines must be in the normal state.

l

The multicast source must exist on the network and the IP address range of the multicast
program must be known.

l

The multicast program must be configured in dynamic generation mode.

Context

The program in the multicast VLAN can be configured statically or generated dynamically.

Dynamic generation mode: A program is dynamically generated according to the program
requested by the user.

l

In this mode, the program list is not required. You need to configure the IP address range
of the program group that can be dynamically generated. The user can request for only the
program whose IP address is within this IP address range.

l

The following functions are not supported: bandwidth management of the multicast
program, user bandwidth management, program preview, and program prejoin.

The program in the multicast VLAN is configured statically by default. Run the

igmp match

mode disable

command to configure the dynamic generation mode.

NOTE

The

igmp match mode

command for configuring the mode of the multicast program can be executed only when

the IGMP mode is off.

Networking

shows the example network of the multicast service.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

430

«
...
439
440
441
442
443
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Wave wifi Страницы: 2

Бренд: Patton electronics Страницы: 8

S5500-HI Switch Series

Бренд: H3C Страницы: 180

Бренд: H3C Страницы: 84

Бренд: H3C Страницы: 281

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 102

S12500CR Series

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 15

H3C S7500E Series

Бренд: H3C Страницы: 1565

Бренд: H3C Страницы: 4

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды