Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 251 / 553

background image

Name: DefaultEmergencyDmm
Type: emergency
Body: (11X|91X)
------------------------------------------
Name: huawei0
Type: normal
Body: ([2-8]xxxxxxx|[2-8]xxSxxxxxxx|13xxxxxxxxx|0xxxxxxxxx|9xxxx|1[0124-9]x|F|
x.F|[0-9].S|15xxxxxxxxx)
------------------------------------------
Name: huawei1
Type: emergency
Body: (11X|91X|0E)
------------------------------------------

7.1.2.5 (Optional) Configuring the Attributes of a PSTN Port

This topic describes how to configure the attributes of a PSTN port to ensure that the PSTN port
can meet the actual application requirements.

Context

The MA5616 supports the following attributes of a PSTN port:

l

Physical attributes (including whether to support the polarity reversal pulse, whether to
support the port locking, and dialing mode). For details about how to configure the physical
attributes of a PSTN port, see

pstnport attribute set

.

l

Electrical attributes (including the impedance and the current). For details about how to
configure the electrical attributes of a PSTN port, see

pstnport electric set

.

l

KC attributes (including the KC charging mode and the valid voltage). For details about
how to configure the KC attributes of a PSTN port, see

pstnport kc set

.

Procedure

Step 1

In global config mode, run the

pstnport

command to enter the PSTN port mode.

Step 2

Run the

pstnport attribute batset

or

pstnport attribute set

command to configure the physical

attributes of a PSTN port.

Step 3

Run the

pstnport electric batset

or

pstnport electric set

command to configure the electrical

attributes of a PSTN port.

Step 4

Run the

pstnport kc batset

or

pstnport kc set

command to configure the KC attributes of the

PSTN port.

Step 5

Check whether the attribute configuration of the PSTN port is the same as the planned data.

l

Run the

display pstnport attribute

command to query the physical attributes of the PSTN

port.

l

Run the

display pstnport electric

command to query the electrical attributes of the PSTN

port.

l

Run the

display pstnport kc

command to query the KC attributes of the PSTN port.

----End

Example

To configure the PSTN ports on the board in slot 0/3 to support the polarity reversal charging,
do as follows:

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

240

«
...
249
250
251
252
253
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: BandLuxe Страницы: 67

Бренд: Harman Kardon Страницы: 66

Бренд: TC Electronic Страницы: 55

Бренд: Yaesu Страницы: 2

Бренд: Konig Страницы: 73

Бренд: Conceptronic Страницы: 230

Power Control Processor

Бренд: ETC Страницы: 64

Core 2 Quad Q9400

Бренд: Intel Страницы: 2

Бренд: ADS Technologies Страницы: 1

Бренд: 3Com Страницы: 32

Бренд: Avaya Страницы: 73

Бренд: Moxa Technologies Страницы: 36

Бренд: Ozenda Страницы: 116

Power System H924

Бренд: IBM Страницы: 48

Бренд: JETWAY Страницы: 47

Бренд: Cradlepoint Страницы: 2

Бренд: Fast Страницы: 66

IntraSwitch 5324MT

Бренд: Asante Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды