manualshive.com logo in svg

Huawei SmartAX MA5616, Руководство по настройке

"Huawei SmartAX MA5616" - высококачественное оборудование для настройки и управления сетями. Здесь вы можете бесплатно скачать "Configuration Manual" и другие руководства по использованию. Посетите manualshive.com, чтобы скачать нужные руководства.

Поделиться
Скачать
background image

Table 5-7

 Default settings of the xPoA-xPoE protocol conversion

Parameter

Default Setting

Maximum number of the MAC addresses in the
MAC address pool

256

Status of the IPoA-IPoE protocol conversion

Disabled

Aging time of the IPoA user forwarding entry

1200s

Status of the PPPoA-PPPoE protocol conversion

Disabled

Status of the MRU negotiation function during the
PPPoA-PPPoE protocol conversion

Disabled

 

Procedure

l

Configure the IPoA-IPoE protocol conversion.

A user can access the Internet in the IPoA mode only after the IPoA-IPoE protocol
conversion is enabled.

1.

In the global config mode, run the 

mac-pool

 command to configure the MAC address

pool, which is used to allocate source MAC addresses to IPoA users. By default, the
number of the MAC addresses in the MAC address pool is 256, which can be changed
by setting parameter 

scope

.

The MAC address encapsulated into packets during the IPoA-IPoE protocol
conversion is the MAC address allocated to the user from the MAC address pool.

2.

Run the 

ipoa enable

 command to enable the IPoA-IPoE protocol conversion. By

default, the IPoA-IPoE protocol conversion is disabled.

3.

Run the 

encapsulation

 command to set the user packet encapsulation mode (select

ipoa

 as the encapsulation mode).

NOTE

l

Configure either the 

ipoa default gateway

 command or the 

dstip

 parameter in the

encapsulation

 command. If the MA5616 works in the L2 mode, set the IP address of the

upper-layer router as the default gateway. If the MA5616 works in the L3 mode, set the IP
address of the L3 interface corresponding to the MA5616 as the default gateway.

l

IPoA encapsulation is not supported in the single-PVC for multiple services application.

l

To switch the encapsulation mode from PPPoA to IPoA, you must change the encapsulation
mode to llc bridge first and then perform switching.

4.

Run the 

ipoa expire-time

 command to set the aging time of the IPoA user forwarding

entry. By default, the aging time of the IPoA user forwarding entry is 1200s. The
default value is recommended.

l

Configure the PPPoA-PPPoE protocol conversion.

A user can access the Internet through the PPPoA dialup only after the PPPoA-PPPoE
protocol conversion is enabled.

1.

In the global config mode, run the 

mac-pool

 command to configure the MAC address

pool, which is used to allocate source MAC addresses to PPPoA users. By default, the
number of the MAC addresses in the MAC address pool is 256, which can be changed
by setting parameter 

scope

.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

5 Configuring the xDSL Internet Access Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

174

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

E-Lins H900 Series User Manual preview
H900 Series
Бренд: E-Lins Страницы: 59
E-Lins H750 Quick Start Manual preview
H750
Бренд: E-Lins Страницы: 11
E-Lins H700 Series Quick Start Manual preview
H700 Series
Бренд: E-Lins Страницы: 9
E-Lins H685 Series Quick Start preview
H685 Series
Бренд: E-Lins Страницы: 5
e-Line Technology Network Video Recorders User Manual preview
Network Video Recorders
Бренд: e-Line Technology Страницы: 34
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Бренд: Lattice Semiconductor Страницы: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Бренд: Lattice Semiconductor Страницы: 13
National Instruments Module NI PXI-8250 User Manual preview
Module NI PXI-8250
Бренд: National Instruments Страницы: 39
IDT TSI384 User Manual preview
TSI384
Бренд: IDT Страницы: 281
DMX4ALL DMX-Universal-Demux User Manual preview
DMX-Universal-Demux
Бренд: DMX4ALL Страницы: 17
Rockwell Automation 41LR4060 Instruction Manual preview
41LR4060
Бренд: Rockwell Automation Страницы: 108
Patton electronics 3087 Quick Start Manual preview
3087
Бренд: Patton electronics Страницы: 12
Endace DAG 7.1S User Manual preview
DAG 7.1S
Бренд: Endace Страницы: 51
TANDBERG D5018501 Hardware User Manual preview
D5018501
Бренд: TANDBERG Страницы: 3
Ruckus Wireless MediaFlex NG Quick Installation Manual preview
MediaFlex NG
Бренд: Ruckus Wireless Страницы: 2
Rosewill RNX-N150RT Quick Installation Manual preview
RNX-N150RT
Бренд: Rosewill Страницы: 10
IMC Networks iMcV-FiberLinX Operation Manual preview
iMcV-FiberLinX
Бренд: IMC Networks Страницы: 36
TDK HHM Series HHM2409 Specifications preview
HHM Series HHM2409
Бренд: TDK Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды