Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 141 / 553

background image

huawei(config)#

display qos-info traffic-statistic port 0/0/1

traffic-statistic:
port 0/0/1:
Inbound:
Matches: Acl 2001 rule 5 running
0 packet

3.14.3.4 Enabling the Mirroring of the Traffic Matching an ACL Rule

This topic describes how to mirror the traffic matching an ACL rule on a port to a specified port.
Mirroring does not affect packet receipt and transmission on the mirroring source port. You can
monitor the traffic of the mirroring source port by analyzing the traffic that passes the mirroring
destination port.

Prerequisite

The ACL and the rule of the ACL are configured, and the port for traffic mirroring is working
in the normal state.

Context

l

The traffic mirror is only valid to permit rules of an ACL.

l

The destination mirroring port cannot be an aggregation port.

l

The system supports only one mirroring destination port and the mirroring destination port
must be the upstream port.

Procedure

Step 1

Run the

traffic-mirror

command to enable the mirroring of the traffic matching an ACL rule

on a specified port.

Step 2

Run the

display qos-info traffic-mirror port

command to query the mirroring information

about the traffic matching an ACL rule on a specified port.

----End

Example

To mirror the traffic that matches ACL 2001 received on port 0/2/0 to port 0/0/1, do as follows:

huawei(config)#

traffic-mirror inbound ip-group 2001 port 0/2/0 to port 0/0/1

huawei(config)#

display qos-info traffic-mirror port 0/2/0

traffic-mirror:
port 0/2/0:
Inbound:
Matches: Acl 2001 rule 5 running
Mirror to: port 0/0/1

3.15 Configuring Environment Monitoring

This topic provides concepts associated with environment monitoring and describes how to
configure environment monitoring on the MA5616.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

130

«
...
139
140
141
142
143
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: M2M Страницы: 9

Бренд: ICP DAS USA Страницы: 48

Бренд: ICP DAS USA Страницы: 24

Бренд: ICP DAS USA Страницы: 4

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

Бренд: Lattice Semiconductor Страницы: 15

Бренд: Pakedge Device & Software Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Zhone Страницы: 2

Бренд: IEI Technology Страницы: 3

Бренд: IDT Страницы: 281

DMX-Universal-Demux

Бренд: DMX4ALL Страницы: 17

Бренд: Rockwell Automation Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды