Huawei S5700 Series Скачать руководство пользователя страница 321

Страница: 321 / 415

Pre-configuration Tasks

Before configuring the PWE3 Ping test on a multi-hop PW, you must correctly configure the
dynamic multi-hop PW or the static multi-hop PW.

Data Preparation

To configure the PWE3 Ping test on a multi-hop PW, you need the following data.

No.

Data

ID of the local end of the PW

ID or IP address of the remote end of the PW

Type of the PW

(Optional) Response mode of the Echo packets, LSP EXP, maximum hops, number
of probes, TTL value, and timeout period of the packets

Type and number of the interface connected with the CE

Start mode and end mode of the test

6.20.2 Configuring Parameters for the PWE3 Ping Test on a Multi-
Hop PW

This part describes how to set PWE3 ping test parameters for a multi-hop PW.

Context

Do as follows on the NQA client:

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

nqa

test-instance

admin-name

test-name

An NQA test instance is created and the test instance view is displayed.

Step 3

Run:

test-type

pwe3ping

The test type is set to PWE3 Ping.

Step 4

(Optional) Run:

vc-type

ldp

The method of setting up a PW is configured.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

310

Содержание S5700 Series
































































































































































































































































































































































































































Результаты поиска

Содержание S5700 Series

Отзывы:

Huawei S5700 Series, Конфигурационное руководство - Управление сетью, Страница: 321 / 415

Результаты поиска

Содержание S5700 Series

Отзывы: