Huawei S5700 Series Скачать руководство пользователя страница 314 | Manualshive

Страница: 314 / 415

Huawei S5700 Series Скачать руководство пользователя страница 314

Applicable Environment

Jitter time refers to the interval for receiving two consecutive packets minus the interval for
sending these two packets.

The process of the ICMP jitter test is as follows:

l

The source sends packets to the destination at a set interval.

l

After receiving a packet, the destination adds a timestamp to the packet and sends it back
to the source.

l

After receiving the returned packets, the source obtains the jitter time by subtracting the
interval for sending the packets from the interval for receiving the packets.

The maximum, minimum, and average jitter time and the maximum unidirectional delay of the
packets from the source to the destination and from the destination to the source are calculated
according to the information received on the source. Based on these data, the network status is
clearly presented.

In the jitter test, you can set the number of packets to be sent consecutively in each test instance.
Through this setting, the actual traffic of a kind of packet during a time period can be simulated.

If the server is a non-Huawei device, you can test the jitter of the network by configuring an
ICMP jitter test instance.

Pre-configuration Tasks

Before configuring an ICMP jitter test, configure a reachable route between the NQA client and
the server.

Data Preparation

To configure a jitter test, you need the following data.

No.

Data

1

Administrator of the NQA test instance and name of the test instance

2

Destination IP address

3

(Optional) Name of a VPN instance, source IP address ,number of test probes sent
each time, number of test packets sent each time, interval for sending test packets,
ratio of the failed NQA tests, and version number of jitter packets

4

Start mode and end mode

6.18.2 Configuring Parameters for the ICMP Jitter Test

This part describes how to set ICMP jitter test parameters.

Context

Do as follows on the NQA client:

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

303

«
...
312
313
314
315
316
...
»

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов