manualshive.com logo in svg

Huawei S5700 Series, Конфигурационное руководство - Управление сетью, Страница: 311 / 415

Поделиться
Скачать
Huawei S5700 Series Скачать руководство пользователя страница 311

No.

Data

3

(Optional) Parameters of the LSP Traceroute test, including the response mode of the
Echo packet, LSP EXP value, maximum hops, probes times, TTL value, and timeout
period of the packets

4

Start mode and end mode of the test

 

6.17.2 Configuring the LSP Trace Parameters for the LDP Tunnel

This part describes how to set parameters for an LDP LSP Trace test.

Context

Do as follows on the NQA client:

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

nqa

 

test-instance

 

admin-name

 

test-name

An NQA test instance is created and the test instance view is displayed.

Step 3

Run:

test-type

 

lsptrace

The test type is set to LSP Trace.

Step 4

Run:

lsp-type

 

ipv4

The tunnel type is set to be the LSP tunnel.

Step 5

Run:

destination-address

 

ipv4

 

ip-address

 { 

lsp-masklen

 

masklen

 | 

lsp-loopback

 

loopback-

address

 }*

The destination IP address to be tested is configured.

Step 6

(Optional) Perform the following as required to configure other parameters for the LSP Trace
test:

l

To configure the response mode of the Echo packet, run the 

lsp-replymode

 { 

no-reply

 |

udp

 | 

udp-via-vpls

 | 

udp-router-alert

 | 

level-control-channel

 } command.

NOTE

In a uni-directional LSP Trace test, if the 

lsp-replymode

 

no-reply

 command is configured, the test

result displays that the test fails regardless of whether the test is successful or fails. If the test is
successful, the test result also displays the number of the timeout packets. If the test fails, the test result
displays the number of the discarded packets.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

300

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов