Huawei S5700 Series Скачать руководство пользователя страница 303 | Manualshive

Страница: 303 / 415

Huawei S5700 Series Скачать руководство пользователя страница 303

6.15 Configuring the LSP Ping Test

This section describes how to configure a Label Switched Path (LSP) ping test to check the
operating status of the LSP.

6.15.1 Establishing the Configuration Task

Before configuring an LSP ping test, familiarize yourself with the applicable environment,
complete the pre-configuration tasks, and obtain the required data. This can help you complete
the configuration task quickly and accurately.

Applicable Environment

The NQA LSP Ping test can be used to test the reachability of the following types of Label
Switched Paths (LSPs) and collect statistics about Link State Advertisement (LSA).

l

LSP tunnels

After the test parameters are configured and the test is started,

1.

NQA creates an MPLS Echo-Request packet and adds the address 127/8 to the IP header
as the destination IP address. The packet is forwarded along the specified LSP in the MPLS
network.

2.

The egress monitors port 3503 that sends Echo packets.

3.

The ingress collects the test results based on the received Echo packets.

Pre-configuration Tasks

Before configuring the LSP Ping test, you need the following configuration:

l

LSP tunnel

Data Preparation

To configure the LSP Ping test, you need the following data.

No.

Data

1

Administrator name and test name

2

For the LSP tunnel: destination IP address and mask of the LSP Ping test

3

(Optional) Parameters of the LSP Ping test, including the response mode of the Echo
packet, packet size, TTL, LSP EXP value, padding character, timeout period of the
packet, probe times, test interval, and percentage of the failed NQA tests

4

Start mode and end mode of the test

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

292

«
...
301
302
303
304
305
...
»

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов