manualshive.com logo in svg

Huawei S5700 Series, Конфигурационное руководство - Управление сетью, Страница: 292 / 415

Поделиться
Скачать
Huawei S5700 Series Скачать руководство пользователя страница 292

Pre-configuration Tasks

Before configuring the TCP test, configure reachable routes between the NQA client and the
TCP server.

Data Preparation

To configure the TCP test, you need the following data.

No.

Data

1

Administrator name and test name

2

IP address and port number monitored by the TCP server

3

(Optional) Destination port numbers of the probe packets sent by the TCP client and
source IP addresses , source port numbers of test packets, interval for sending test
packets, and percentage of the failed NQA tests

4

Start mode and end mode of the test

 

6.12.2 Configuring the TCP Server

The IP address and number of the port monitored by the server must be identical with those
configured on the client.

Context

Do as follows on the NQA server (TCP server):

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

nqa-server tcpconnect

 [ 

vpn-instance

 

vpn-instance-name

 ] 

ip-address

 

port-number

The TCP monitoring service is configured.

NOTE

Note that the IP address and port number monitored by the server should be consistent with those configured
on the client.

Only S5700EI and S5700HI support 

vpn-instance

 

vpn-instance-name

.

----End

6.12.3 Configuring the TCP Client

This part describes how to set TCP test parameters.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

281

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов