Huawei RRU3971 Скачать руководство пользователя

Страница: 121 / 134

Figure 8-28

Installing a CPRI optical cable

NOTICE

To avoid any damage to optical cables, the cables connected to the RRU must be installed
according to the installation process. For details about the installation process, see

8.3 Installing

RRU Cables

Step 3

Connect the end labeled 2A and 2B of the optical cable to the optical module on the BBU side.

Step 4

Route the cables according to the instructions in

8.1 Cabling Requirements

, and then use cable

ties to bind the cables.

Step 5

Label the installed cables according to the instructions in Attaching an L-Shaped Label.

----End

8.11 Installing an RRU Power Cable

This section describes the procedure for installing an RRU power cable.

Prerequisites

A tool-less female connector (pressfit type) is added to the RRU power cable on the RRU
side. For details, see

11.1 Adding a Tool-Less Female Connector (Pressfit Type) to the

RRU Power Cable on the RRU Side

8 Installing RRU Cables

Issue ()

Huawei Proprietary and Confidential

112

Содержание RRU3971







































































































































Результаты поиска

Содержание RRU3971

Отзывы:

Похожие инструкции для RRU3971

Бренды по названию

Популярные бренды

Huawei RRU3971, Руководство по установке

Результаты поиска

Содержание RRU3971

Отзывы:

Похожие инструкции для RRU3971

Бренды по названию

Популярные бренды