Huawei RRU3632 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 129

background image

Figure 3-23

Six RRUs installed on an IFS06

(1) Height-restricted scenario

(2) Height-unrestricted scenario

3.5 Installation Clearance Requirements of an RRU

This section describes the requirements for the installation clearance of a single RRU and
multiple RRUs and the requirements for the installation spacing between RRUs.

3.5.1 Clearance for a Single RRU

This section describes the recommended and minimum clearance for a single RRU.

NOTICE

If an RRU is installed on the bitumen ground, the RRU must be at least 500 mm (700 mm or
more as recommended) away from the bitumen ground. The following describes the space
requirements for installing a single RRU on the non-bitumen ground.

RRU3832&RRU3632
Installation Guide

3 Information About the Installation

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

26

«
...
33
34
35
36
37
...
»

Содержание RRU3632


































































































































Отзывы:

Нет отзывов

Похожие инструкции для RRU3632

PCMCIA WIRELESS ASAPTER DWL-650

Бренд: D-Link Страницы: 5

PowerLine DHP-W611AV

Бренд: D-Link Страницы: 78

ER3-100 (5K02-55)

Бренд: 8e6 Technologies Страницы: 74

Бренд: Abocom Страницы: 1

Бренд: Teknim Страницы: 10

Бренд: E-Lins Страницы: 9

Бренд: Nvidia Страницы: 115

Бренд: ZyXEL Communications Страницы: 2

Бренд: Ubiquiti Страницы: 20

Бренд: Hunter Страницы: 2

Бренд: Hawking Страницы: 21

TGXPS-1080-M12-MV Series

Бренд: ORiNG Страницы: 2

Network Adapter AC AAP

Бренд: Extron electronics Страницы: 2

Бренд: CyberResearch Страницы: 59

Бренд: LevelOne Страницы: 83

Бренд: ST Страницы: 37

Бренд: JETWAY Страницы: 15

Бренд: Siklu Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды