Huawei R100020G1 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 53

background image

ventilation area of the system is calculated based on the number of modules.

(The data is the heat dissipation area required for the charging module only.)

●

It is recommended that the space reserved at the air intake vent and exhaust

vent of the charging module be at least 40 mm and 85 mm respectively. The

actual space depends on the system air channel.

●

The installation environment must meet the environmental specifications. For

details, see "Technical Specifications."

4.3 Installing a Charging Module

Installation Clearances

Figure 4-2 Installation clearances (unit: mm)

Installation Procedure

CA UTION

Do not keep the installed charging module in the standby or power-off state for

an extended period.

NO TE

● Ensure that all the mounting holes on the panel are secured by screws.
● Ensure that the nixie tubes are on the left side of the charging module during horizontal

mounting. Ensure that the nixie tubes are on the upper side of the charging module

during side mounting.

● The charging module supports horizontal-mounting and side-mounting installation.

Select the installation mode based on the actual situation. The horizontal-mounting

installation mode is recommended.

Step 1 Slowly push the charging module into the slot.

R100020G1 Charging Module

User Manual

4 Installation

Issue 05 (2021-11-16) Copyright © Huawei Digital Power Technologies Co., Ltd.

25

«
...
29
30
31
32
33
...
»

Содержание R100020G1






















































Отзывы:

Нет отзывов

Похожие инструкции для R100020G1

Бренд: CCL Страницы: 6

Belt-Pack B1245

Бренд: Sachtler Страницы: 24

Multi-Battery Charger

Бренд: Cognex Страницы: 2

Бренд: Coleman Страницы: 2

Бренд: Makita Страницы: 8

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды