Huawei R100020G1 Скачать руководство пользователя страница 19

Страница: 19 / 53

Display

Description

Mode

● Auo is displayed by default in standard mode. The

charging module works under the system monitoring

command.

● dEG indicates the setting mode.

1. The output voltage, output current, and startup/

shutdown can be set only in this mode. The settings

become invalid upon mode exiting.

2. The charging module can run properly without

being connected to the system monitoring module.

● The Auo and dEG modes can be switched using

buttons.

Status code

● The high-order character is displayed as H, and the

middle- and low-order characters are displayed as

digits.

● Parameters cannot be set using buttons.

Table 2-5 Status code mapping

Status

Code

Status Description

H00

Default status

H01

Silent mode

H02

Input derating

H03

Temperature derating

H04

Air filter blocked

H05

Manual switching mode

H06

250 kbps baud rate

H07

Customer version configuration mode

2.4.4 Button Operations

The buttons allow you to set the output voltage, output current, hardware

address, and group number, and to start or shut down the charging module.

●

Press the left button (for at least 0.25s) to turn the displayed screen or switch

the high-, middle-, and low-order nixie tubes.

●

Press the right button (for at least 0.25s) to turn the displayed screen or

increase or decrease digits.

R100020G1 Charging Module

User Manual

2 Overview

Содержание R100020G1






















































Результаты поиска

Содержание R100020G1

Отзывы:

Похожие инструкции для R100020G1

Бренды по названию

Популярные бренды

Huawei R100020G1, Руководство пользователя

Результаты поиска

Содержание R100020G1

Отзывы:

Похожие инструкции для R100020G1

Бренды по названию

Популярные бренды