Huawei R100020G1 Скачать руководство пользователя страница 14

Страница: 14 / 53

●

Standard mode: The module supports 20 kW full power and its noise does not

exceed 60 dB under rated conditions.

Display Panel

The display panel of the charging module consists of three indicators, three nixie

tubes, and two buttons.

●

The indicators show the running status of the charging module.

●

The nixie tubes display the output voltage, output current, hardware address,

group number, startup/shutdown status, software version, or error code of the

charging module.

●

The buttons allow you to set the output voltage, output current, hardware

address, and group number, and to start or shut down a charging module.

NO TE

If the hardware addresses and group numbers of two modules are the same, the modules

report an alarm indicating that the hardware addresses are duplicate.

Grouping and Address Allocation

●

You can set the groups for charging modules on the system monitoring

module. Charging modules in a group can automatically implement current

sharing control.

●

Software addresses are automatically allocated to the charging modules in a

group to facilitate module identification. Note that the software address may

be different from the slot number of the charging pile.

●

The hardware address of a charging module can be set to stay consistent with

the slot number of the charging pile. The charging module saves the

hardware address upon power-off.

NO TE

● The software address will be reallocated after adding, reducing, or replacing a charging

module.

● If an alarm is generated indicating that the hardware address of the module is duplicate

after the charging module is moved from one charging pile to another, reset the

hardware address first and then the group number of that module. After the hardware

address is modified, the group number is restored to the default value.

2.2 Key Features

●

Wide input voltage range: 260–528 V AC

●

Wide operating temperature range: –35°C to +75°C

●

Rated output voltage: 1000 V DC

●

High output efficiency: peak efficiency up to 96.55%

●

Maximum output power: 20 kW

●

Hot swappable

●

Intelligent adjustment of fan speed

●

CAN bus communication

R100020G1 Charging Module

User Manual

2 Overview

Содержание R100020G1






















































Результаты поиска

Содержание R100020G1

Отзывы:

Похожие инструкции для R100020G1

Бренды по названию

Популярные бренды

Huawei R100020G1, Руководство пользователя

Результаты поиска

Содержание R100020G1

Отзывы:

Похожие инструкции для R100020G1

Бренды по названию

Популярные бренды