manualshive.com logo in svg

Huawei PowerCube 5000, Руководство по установке, Страница: 90 / 103

Поделиться
Скачать
Huawei PowerCube 5000 Скачать руководство пользователя страница 90

PowerCube 5000 (SUN2000-150KTL-S0) 
Installation Guide 

9 Power-on and Commissioning 

 

Issue 03 (2020-04-10) 

Copyright © Huawei Technologies Co., Ltd. 

84 

 

9.6 CIM and BIM Networking 

Prerequisites 

Before networking, ensure that all the CIMs and BIMs have no network parameters, that is, 
the RF_Z indicator on the CIM is steady green and the RUN/ALM indicator on the BIM is 
steady red. 

 

 

 

If the RF_Z indicator on the CIM is not steady green, hold down the networking switch on 
the CIM for 10–20s to clear the original network. 

 

If the RUN/ALM indicator on the BIM is not steady red, hold down the networking switch 
on the BIM for at least 5s to clear the original network. 

Context 

During networking, only one CIM can be in networking state, that is, the RF_Z indicator of 
the CIM is blinking at super short intervals. 

Procedure 

Step 1

 

Hold down the networking switch on the CIM for 2s. The ALM indicator blinks red once, and 
the RF_Z indicator turns from steady green to blinking green at super short intervals, which 
indicates that the CIM is being networked. 

Figure 9-9

 

CIM 

 

(1) Networking switch 

(2) ALM indicator 

(3) RF_Z indicator 

 

Step 2

 

Hold down the networking switch on the BIM for 2s and release the switch. The RUN/ALM 
indicator on the BIM turns from steady red to blinking green at super short intervals and then 
blinking green at long intervals at last, indicating that the BIM searches for and connects to 
the CIM network. 

Содержание PowerCube 5000








































































































Отзывы:

Нет отзывов