Huawei PowerCube 5000 Скачать руководство пользователя страница 73

Страница: 73 / 103

PowerCube 5000 (SUN2000-150KTL-S0)
Installation Guide

8 Installation Verification

Issue 03 (2020-04-10)

Installation Verification

After installing the cabinet and all equipment, check the installation items, installation
environment, and cables.

Checking the Cabinet Installation

Table 8-1

Cabinet installation checklist

No. Check That

Result

The cabinet is placed in accordance with the design
drawing.

□ Yes □ No

The base is secured.

□ Yes □ No

All bolts, especially the bolts used for electrical
connections, are fully tightened. Flat washers and spring
washers are all installed in correct sequence.

□ Yes □ No

The cabinet is clean, free of dust and dirt.

□ Yes □ No

All labels are correct, clear, and complete.

□ Yes □ No

Checking the Environment

Table 8-2

Environment checklist

No. Check That

Result

There are no unnecessary adhesive tape or cable ties on
cables.

□ Yes □ No

There are no adhesive tapes, cable ties, paper scraps, or
packing materials around the cabinet.

□ Yes □ No

Содержание PowerCube 5000








































































































Результаты поиска

Содержание PowerCube 5000

Отзывы:

Huawei PowerCube 5000, Руководство по установке, Страница: 73 / 103

Результаты поиска

Содержание PowerCube 5000

Отзывы: