Huawei PowerCube 5000 Скачать руководство пользователя страница 69

Страница: 69 / 103

PowerCube 5000 (SUN2000-150KTL-S0)
Installation Guide

7 Installing Cables

Issue 03 (2020-04-10)

Step 2

Connect the signal cable from the battery temperature sensor to the BTEMP terminal on the
UIM02C, as shown in the following figure.

Figure 7-21

Installing the signal cable for a battery temperature sensor

----End

7.9 Installing AC Input Power Cables

Prerequisites

AC input power cables need to be installed when a backup DG is available.



Ensure that the upstream AC input circuit breaker is OFF, and attach labels such as "No
operations allowed."



Switch off all circuit breakers before installing power cables.

Procedure

Step 1

Prepare a suitable length cable based on site requirements. Install a cord end terminal or an
OT terminal on each end of the cable.

Step 2

Install AC input power cables.

Содержание PowerCube 5000








































































































Результаты поиска

Содержание PowerCube 5000

Отзывы:

Huawei PowerCube 5000, Руководство по установке, Страница: 69 / 103

Результаты поиска

Содержание PowerCube 5000

Отзывы: