Huawei NetCol5000-C030H90D0 страница 76 Скачать руководство пользователя

Страница: 76 / 206

Figure 3-49 Signal ports

(1) Common alarm 2 (ALM_2 COM)

(2) Common alarm 2 (ALM_2 NO)

(3) Common alarm 1 (ALM_1 COM)

(4) Common alarm 1 (ALM_1 NO)

(5) External water sensor (Water -)

(6) External water sensor (Water +)

(7) Remote on/off (Remote COM)

(8) Remote on/off ()

(9) Smoke sensor (Smoke AI)

(10) Smoke sensor (Smoke 12VDC)

3.12.4.3 Connecting the Teamwork Network Cable

NO TICE

● Smart cooling products in a teamwork group must be of the same model.
● The default networking mode is CAN networking.
● The smart cooling product supports two teamwork networking modes: FE

teamwork networking and CAN teamwork networking (hand-in-hand).

3.12.4.3.1 Connecting the FE Teamwork Network Cable

Procedure

Step 1 (Optional) Make FE teamwork network cables by referring to

Figure 3-50

required onsite.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

3 Installation

Issue 03 (2020-08-30)

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030H90D0, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды