Huawei NetCol5000-C030H90D0 страница 65 Скачать руководство пользователя | Manualshive

Страница: 65 / 206

background image

Figure 3-34 Connecting the water inlet and outlet pipes (NetCol5000-C030/C032)

----End

3.8.3.2 Connecting Aluminum Plastic Pipes

Procedure

Step 1 Open the rear door and remove the air filter.

Step 2 Knock off the knock-out holes for the chilled water inlet and outlet pipes.

NO TICE

● Ensure that pipes and power cables are routed through separate holes.
● Do not prepare extra knock-out holes to avoid performance loss.
● In connecting the pipes, ensure that the aluminum plastic pipes are in proper

contact with the straight male connectors.

● In connecting the pipes, avoid violent shake.
● NetCol5000-C030/C032 need to make the holes for the chilled water inlet and

outlet pipes using a knife.

Step 3 Remove the water pipe plug using an open-end wrench.

Step 4 Apply screw thread sealant evenly on the connecting position of external screw

threads of the straight male connector, and use a torque wrench and a common

wrench in collaboration to secure the straight male connector to the connector on

the device.

Step 5 Install the sealing ring and nut at the end of the aluminum plastic pipe that ran

through the hole rubber ring.

Step 6 After the aluminum plastic pipe and the straight male connector are connected,

secure them to the aluminum plastic pipe with the installed sealing ring and nut.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

3 Installation

Issue 03 (2020-08-30)

Copyright © Huawei Technologies Co., Ltd.

57

«
...
63
64
65
66
67
...
»

Содержание NetCol5000-C030H90D0















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NetCol5000-C030H90D0

Pathfinder AWV Series

Бренд: Daikin Страницы: 92

Бренд: Stiga Страницы: 29

Бренд: S&A Страницы: 15

FTS FLEXICOOL IMMERSION COOLERS FC100

Бренд: SP Scientific Страницы: 38

Бренд: Green Technik Страницы: 39

Бренд: Land Pride Страницы: 36

Бренд: Scheppach Страницы: 56

Бренд: SMC Networks Страницы: 20

HRL100-A*-20 Series

Бренд: SMC Networks Страницы: 76

Бренд: Ryobi Страницы: 30

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: Farmi Forest Страницы: 128

Trailblazer AGZ030E-070E

Бренд: Daikin Страницы: 148

Бренд: UNIA Страницы: 34

Бренд: Häfele Страницы: 11

Бренд: Yard Machines Страницы: 20

Бренд: Quantech Страницы: 62

Бренд: York Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды