Huawei LUNA2000-30-S0 Скачать руководство пользователя

Страница: 81 / 129

NO TICE

● Keep the DC input BAT+ cable and BAT– cable close to each other.
● Cables with high rigidity, such as armored cables, are not recommended as DC

input power cables to avoid cable folding.

● Before assembling DC connectors, label the cable polarities correctly to ensure

correct cable connections.

● After crimping the positive and negative metal terminals, pull the DC input

power cables back to ensure that they are connected securely.

● Insert the crimped metal terminals of the positive and negative power cables

into the appropriate positive and negative connectors. Then pull back the DC

input power cables to ensure that they are connected securely.

Step 2 Insert the positive and negative connectors into the battery terminals (BAT+ and

BAT-) on the switch and connect the other end to the cascaded battery.

Figure 5-12 Connecting battery cables

----End

5.3.3 Installing a Signal Cable

Connecting the Signal Cable between the Power Control Module and the

Inverter

NO TICE

When laying out a signal cable, separate it from power cables and keep it away

from strong interference sources to prevent communication interruption.

The COM port definitions on both sides of the power control module are the

same. It is recommended that the COM port on the switch side be connected to

the inverter and the COM port on the other side be connected to the cascaded

battery.

LUNA2000-(5-30)-S0

User Manual

5 Electrical Connection

Issue 07 (2022-01-10)

Содержание LUNA2000-30-S0


































































































































Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Похожие инструкции для LUNA2000-30-S0

Бренды по названию

Популярные бренды

Huawei LUNA2000-30-S0, Руководство пользователя

Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Похожие инструкции для LUNA2000-30-S0

Бренды по названию

Популярные бренды