Huawei LUNA2000-30-S0 Скачать руководство пользователя страница 80

Страница: 80 / 129

NO TE

● It is recommended that silica gel or paint be used around the ground terminal after the

PE cable is connected.

----End

5.3.2 Installing DC Input Power Cables

Connect DC input power cables to the inverter

Insert the positive and negative battery connectors (Staubli) into the

corresponding DC input terminals (BAT+ and BAT–).

NO TE

The DC input terminals (BAT+ and BAT–) on the left and right sides of the battery are the

same.

Step 1 Assemble DC connectors.

Figure 5-11 Assembling DC connectors

CA UTION

For battery terminals, use the delivered Staubli MC4 positive and negative metal

terminals and DC connectors. Using incompatible positive and negative metal

terminals and DC connectors may burn the cables or damage the module. The

resulting device damage will not be covered under warranty.

LUNA2000-(5-30)-S0

User Manual

5 Electrical Connection

Issue 07 (2022-01-10)

Содержание LUNA2000-30-S0


































































































































Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Похожие инструкции для LUNA2000-30-S0

Бренды по названию

Популярные бренды

Huawei LUNA2000-30-S0, Руководство пользователя

Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Похожие инструкции для LUNA2000-30-S0

Бренды по названию

Популярные бренды