Huawei LUNA2000-30-S0 Скачать руководство пользователя страница 124

Страница: 124 / 129

8.2 LUNA2000-5-E0

Technical Specifications

LUNA2000-5-E0

Nominal available capacity

5 kWh

Battery cell type

Li-ion

Dimensions (H x W x D)

360 mm x 670 mm x 150 mm

Weight

50 kg

Cooling mode

Free cooling

IP rating

IP66

Operating temperature

–20°C to +55°C

Maximum operating

altitude

4000 m

Note a: The initial capacity (design capacity) of the battery modules is 5 kWh. The actual capacity

may vary depending on the environment conditions, such as temperature, transportation

conditions, and storage conditions.

8.3 SUN2000-Related

Table 8-1 SUN2000-(2KTL-6KTL)-L1

Parameter SUN200

0-2KTL-

SUN2000

-3KTL-L1

SUN2000

-3.68KTL-

SUN2000

-4KTL-L1

SUN2000

-4.6KTL-

SUN2000

-5KTL-L1

SUN2000

-6KTL-L1

Off-grid

power

2000 W

3000 W

3680 W

4000 W

4600 W

5000 W

6000 W

Charging

power

from grid

to inverter

2200 W

3000 W

Battery

port power

5000 W

LUNA2000-(5-30)-S0

User Manual

8 Technical Specifications

Issue 07 (2022-01-10)

117

Содержание LUNA2000-30-S0


































































































































Результаты поиска

Содержание LUNA2000-30-S0

Отзывы:

Huawei LUNA2000-30-S0, Руководство пользователя, Страница: 124 / 129

Результаты поиска

Содержание LUNA2000-30-S0

Отзывы: