Huawei LampSite Скачать руководство пользователя

Страница: 70 / 100

Step 3

Fit the four hooks of the pRRU into the installation kits, as shown in

Figure 5-18

. If the hooks

are properly installed, a slight clack can be heard.

NOTE

It is recommended that you observe the installation from one side of the pRRU when inserting hooks into
the kits.

Figure 5-18

Installing a pRRU

----End

5.4.5 pRRU Installed on a Plate

If the plate on the ceiling has sufficient load bearing capacity and space installation, the pRRU
can be installed on the plate of the ceiling indoors.

Procedure

Step 1

Determine the position for installing the pRRU based on the construction blueprint and the space
requirements.

NOTE

For pRRU installation space requirements, see

5.1.3 Space Requirements

Step 2

Place the plate in the installation position against the wall. Then, level the plate and mark the
two anchor points using a marker, as shown in

Figure 5-19

LampSite
Installation Guide

5 Installing a pRRU

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Содержание LampSite





































































































Результаты поиска

Содержание LampSite

Отзывы:

Похожие инструкции для LampSite

Бренды по названию

Популярные бренды

Huawei LampSite, Руководство по установке

Результаты поиска

Содержание LampSite

Отзывы:

Похожие инструкции для LampSite

Бренды по названию

Популярные бренды