Huawei LampSite Скачать руководство пользователя

Страница: 23 / 100

4.2 Installation Process

The RHUB installation involves installing an RHUB module, installing RHUB cables, checking
the RHUB hardware installation, and powering on the RHUB.

Figure 4-11

shows the RHUB installation process.

Figure 4-11

RHUB installation process

4.3 Installing an RHUB

An RHUB can be installed in a cabinet, rack, shelf, or on a wall.

4.3.1 Installing an RHUB in a 19-Inch Cabinet or Rack

This section describes how to install an RHUB in a 19-inch cabinet.

Procedure

The following describes how to install an RHUB with mounting ears in reverse mode:

NOTE

If necessary, request one more person for assistance.

With one hand holding it, align the mounting holes with the installation holes, slowly
push the RHUB into the required position in the cabinet, as shown in

Figure 4-12

LampSite
Installation Guide

4 Installing an RHUB

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Содержание LampSite





































































































Результаты поиска

Содержание LampSite

Отзывы:

Похожие инструкции для LampSite

Бренды по названию

Популярные бренды

Huawei LampSite, Руководство по установке

Результаты поиска

Содержание LampSite

Отзывы:

Похожие инструкции для LampSite

Бренды по названию

Популярные бренды