Huawei IPC6125-WDL-FA Скачать руководство пользователя страница 49

Страница: 49 / 202

Setting Video Parameters

About This Chapter

This section describes how to set video parameters, such as video and audio stream
parameters.

6.1 Setting Video and Audio Stream Parameters

You can set video and audio parameters based on the site requirements.

By configuring a stream package, you can predefine several common video and audio stream
parameters for quick invoking in the future.

6.3 Setting ISP Parameters

By setting Image Signal Processing (ISP) parameters, you can adjust video images to adapt to
different surveillance scenarios.

6.4 Configuring an ISP Package

You can configure a daily or yearly plan for scheduled tasks of ISP packages.

6.5 Setting Area Metering

If area metering is configured, different areas possess different metering weights. Area
metering configuration is applicable to scenarios with prominent subjects.

6.6 Setting ROI Parameters

By setting a region of interest (ROI), you can set the ROI quality to differentiate the ROI from
other image regions. The ROI effect is prominent at a low bit rate.

6.7 Setting the Focusing Region

If you set a focusing region for a camera, the camera preferentially focuses on the focusing
region.

6.8 Setting Image Overlay

You can set image overlay to specify the position where the image is displayed.

6.9 Setting Privacy Mask Parameters

You can set a privacy mask area on the live video for privacy protection.

6.10 Setting Motion Detection Parameters

An alarm is generated when an object moves within the specified surveillance range of the
camera.

IPC6125-WDL-FA
Configuration Guide

6 Setting Video Parameters

Issue 01 (2016-08-20)

Huawei Proprietary and Confidential

Содержание IPC6125-WDL-FA











































































































































































































Результаты поиска

Содержание IPC6125-WDL-FA

Отзывы:

Похожие инструкции для IPC6125-WDL-FA

Бренды по названию

Популярные бренды

Huawei IPC6125-WDL-FA, Руководство по настройке

Результаты поиска

Содержание IPC6125-WDL-FA

Отзывы:

Похожие инструкции для IPC6125-WDL-FA

Бренды по названию

Популярные бренды