manualshive.com logo in svg

Huawei FusionServer Pro 2288H V5, Руководство пользователя, Страница: 32 / 177

Поделиться
Скачать
Huawei FusionServer Pro 2288H V5 Скачать руководство пользователя страница 32

Table 2-7

 DDR4 memory specifications

Parameter

Specifications

Maximum capacity per DDR4 memory module (GB)

128

Rated speed (MT/s)

2933

Operating voltage (V)

1.2

Maximum number of DDR4 memory modules in a server

a

24

Maximum DDR4 memory capacity of the server (GB)

b

3072

Maximum operating speed
(MT/s)

1DPC

d

2933

c

2DPC

d

2666

l

a: The maximum number of DDR4 memory modules is based on dual-processor
configuration. The value is halved for a server with only one processor.

l

b: The maximum DDR4 memory capacity varies depending on the processor type. The
value listed in this table is based on the assumption that memory modules are fully
configured.

l

c: If the Cascade Lake processor is used, the maximum operating speed of a memory
module can reach 2933 MT/s. If the Skylake processor is used, the maximum operating
speed of a memory module can reach 2666 MT/s only.

l

d: 1DPC means 1 DIMM per channel, and 2DPC means 2 DIMMs per channel.

 

2.4.4 Memory Installation Guidelines

l

Observe the following when configuring DDR4 memory modules:

–

Install memory modules only when corresponding processors are installed.

–

Do not install LRDIMMs and RDIMMs in the same server.

–

Install filler memory modules in vacant slots.

l

Observe the following when configuring DDR4 memory modules in specific operating
mode:

–

Memory sparing mode

n

Comply with the general installation guidelines.

n

Each memory channel must have a valid online spare configuration.

n

The channels can have different online spare configurations.

n

Each populated channel must have a spare rank.

–

Memory mirroring mode

n

Comply with the general installation guidelines.

n

Install memory modules for channels 1 and 2 or channels 3 and 4. The
memory modules installed must be identical in size and organization.

n

For a multi-processor configuration, each processor must have a valid memory
mirroring configuration.

FusionServer Pro 2288H V5 Server
User Guide

2 Hardware Description

Issue 08 (2019-10-30)

Copyright © Huawei Technologies Co., Ltd.

24

Содержание FusionServer Pro 2288H V5


















































































































































































Отзывы:

Нет отзывов