Huawei FusionModule2000 V500R003C10 Скачать руководство пользователя страница 42

Страница: 42 / 217

FusionModule2000 Smart Modular Data Center
Product Description

5 Power Supply and Distribution System

Issue 06 (2020-05-21)

Silk

Screen

Description

Status

Initial Status

EPO_NC

EPO port

If the normally closed
(NC) port is
disconnected from the
EPO_12V port, EPO
is triggered.

Connected

EPO_12V

+12 V

SWITCH
STATUS_
OUT

Port for monitoring the UPS
output circuit breaker



Connected: circuit
breaker ON



Disconnected:
circuit breaker
OFF

Connected

SWITCH
STATUS_
0V

Port for signal ground

SWITCH
STATUS_
MT

Port for monitoring the
maintenance circuit breaker



Disconnected:
circuit breaker ON



Connected: circuit
breaker OFF

Disconnected

SWITCH
STATUS_
0V

Port for signal ground

SWITCH
STATUS_
BP

Port for monitoring the
bypass input circuit breaker



Connected: circuit
breaker ON



Disconnected:
circuit breaker
OFF

Connected

SWITCH
STATUS_
0V

Port for signal ground

SPD

Port for monitoring the
input AC surge protective
device (SPD)



Connected: SPD
enabled



Disconnected:
SPD disabled

Connected

Port for signal ground



The dry contact interface card takes effect only after it is set on the monitoring system. Set the
unused dry contact signal to the unused status.



Set the EPO port to NO or NC as required.



When multiple UPSs are paralleled, all dry contact signals to be used need to connect to each UPS.



Single cables require dual-insulated twisted cables. If the length of a power cable is within 25–50 m,
its cross-sectional area must be 0.5 mm

to 1.5 mm

5.2.1.4.4 Monitoring Interface Card

Содержание FusionModule2000 V500R003C10


























































































































































































































Результаты поиска

Содержание FusionModule2000 V500R003C10

Отзывы:

Похожие инструкции для FusionModule2000 V500R003C10

Бренды по названию

Популярные бренды

Huawei FusionModule2000 V500R003C10, Описание продукта

Результаты поиска

Содержание FusionModule2000 V500R003C10

Отзывы:

Похожие инструкции для FusionModule2000 V500R003C10

Бренды по названию

Популярные бренды