Huawei FusionModule1000A Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 108

background image

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

10 Removing Transport Protection Materials from Fire

Extinguishing and Monitoring Devices

Issue 03 (2020-06-09)

Copyright © Huawei Technologies Co., Ltd.

79

10

Removing Transport Protection

Materials from Fire Extinguishing and

Monitoring Devices

Prerequisites

The pre-fab. modules have been installed.

Context

Protection materials are installed for fire extinguishing and monitoring devices to prevent
them from falling off or being damaged due to strong vibration during FusionModule1000
transportation.

To prevent damage to aisle floors in the FusionModule1000, you are advised to remove the protective
films after the FusionModule1000 is installed.

Preparations

Tools: step ladder

Materials: none

Documents: fire extinguishing device layout diagram, monitoring device layout diagram

Skill requirement: common technician

Procedure

Step 1

Understand the internal layout of the FusionModule1000 by referring to the fire extinguishing
device layout diagram and monitoring device layout diagram.

Step 2

Remove the transport protection materials from the top of the aisles inside the
FusionModule1000.

Table 10-1

Transport protection materials to be removed

No.

Device

Protection Materials

«
...
84
85
86
87
88
...
»

Содержание FusionModule1000A













































































































Отзывы:

Нет отзывов

Похожие инструкции для FusionModule1000A

Бренд: HGST Страницы: 2

Бренд: GrainPro Страницы: 19

BARRACUDA 7200.10 ST3160215AS

Бренд: Seagate Страницы: 2

Бренд: DeWalt Страницы: 76

HTS722010K9A300

Бренд: Hitachi Страницы: 4

USB STORiUM N DRIVE

Бренд: HANBiT Electronics Страницы: 14

Бренд: Allnet Страницы: 91

Бренд: ABSCO SHEDS Страницы: 45

Cavalry ACSSDS32F

Бренд: Cavalry Страницы: 1

Бренд: Cavalry Страницы: 20

CADA-SA8 Series

Бренд: Cavalry Страницы: 20

SuperStorageSystem SSG-2028R-DN2R48L

Бренд: Supermicro Страницы: 85

Бренд: Grizzly Страницы: 2

Бренд: Grizzly Страницы: 6

Бренд: Grizzly Страницы: 32

Бренд: red lion Страницы: 8

IronWolf ST6000VN001

Бренд: Seagate Technology Страницы: 35

CHALLENGE CMN A012B

Бренд: Silicon Graphics Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды