Huawei FusionModule1000A Скачать руководство пользователя | Manualshive

Страница: 21 / 108

background image

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

4 Installing Pre-fab. Modules

Issue 03 (2020-06-09)

Copyright © Huawei Technologies Co., Ltd.

14

4

Installing Pre-fab. Modules

4.1 (Optional) Concrete Platform Scenario

4.1.1 Determining the Pre-fab. Module Installation Position

Prerequisites



The field meets site requirements.



Before installing pre-fab. modules, check the height of concrete platforms and ensure
that the height (altitude) error between the upper surfaces of all platforms does not
exceed 5 mm.

Concrete platform levelness is critical to pre-fab. module installation. Ensure that the concrete
platform meet requirements before installing pre-fab. modules.

Context

Before installing pre-fab. modules, determine their installation positions and directions based
on site space.

Preparations

Tools: marker, ink foundation, long leather measuring tape

Materials: none

Skill requirement: skilled technician

Procedure

Step 1

Determine the reference points for installing pre-fab. modules on the concrete platforms.
Mark the reference points using a marker.

Step 2

On the basis of the reference points, mark the mounting positions for the four corner fittings
of a pre-fab. module using an ink fountain and long leather measuring tape.

«
...
19
20
21
22
23
...
»

Содержание FusionModule1000A













































































































Отзывы:

Нет отзывов

Похожие инструкции для FusionModule1000A

Бренд: ABSCO SHEDS Страницы: 26

FlashPoint ShareDrive

Бренд: Xmultiple Страницы: 16

Fairmont Garden Shed

Бренд: YardCraft Страницы: 29

Бренд: POCKetec Страницы: 19

Бренд: Hanover Страницы: 12

OMNISTOR 4000f SERIES

Бренд: Rackable Systems Страницы: 112

GridLine 930505

Бренд: GARANT Страницы: 116

Бренд: garofalo Страницы: 20

Бренд: HGST Страницы: 51

SmartStore SM2520

Бренд: Riverlea Страницы: 16

Бренд: Addonics Technologies Страницы: 8

Footprint Radius Profile Undersurface Storage

Бренд: Kimball Страницы: 6

AccessPoint 001890

Бренд: GE Страницы: 2

Digital Video Storage System

Бренд: GE Страницы: 24

Monogram ZWVS1000SR

Бренд: GE Страницы: 40

Бренд: D-Link Страницы: 69

ShareCenter Pro DNS-1200-05

Бренд: D-Link Страницы: 170

Бренд: LaCie Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды