Huawei FusionCol8000-E240 Скачать руководство пользователя страница 125

Страница: 125 / 305

6.4.4.1 Setting Communications Parameters (Modbus RTU Protocol)

Procedure

Step 1 On the home screen, choose Settings > Comm Settings > Modbus Settings.

Figure 6-7 Modbus Settings

Step 2 Set the baud rate, communication address, and RS485 monitoring group.

Table 6-7 Baud rate and communications address settings

Parameter Setting

Setting Method

Baud rate

9600, 19200

Set the baud rate as required. The value should be

consistent with that set on the NMS.

Communic

ation

address

1–255

Set the communication address of the smart

cooling product as planned. The NMS

communicates with the smart cooling product

through this address, and the communication

addresses of two smart cooling products

connecting to the same NMS must be unique.

RS485

monitoring

grouping

Enable,

Disable

● For scenarios without grouping, set this

parameter to Enable for the last device.

● For scenarios with grouping, set this parameter

to Enable for the last device in each teamwork

control group.

----End

6.4.4.2 Setting Communications Parameters (Modbus TCP Protocol)

Context

This section applies to the scenario where the device is connected to the NMS.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

6 Power-On Commissioning

Issue 02 (2021-04-15)

116

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды