Huawei FusionCol8000-E24 Скачать руководство пользователя страница 188

Страница: 188 / 269

Step 7 Secure the new compressor using a solid wrench.

Step 8 Weld the suction inlet and exhaust outlet with the compressor using a welding

torch.

NO TICE

● During welding, use a silver copper welding rod containing 5% silver. Check

that the welding joints are in good condition, without poor welding.

● To avoid burning the internal components, other pipes, thermal insulation

foam, cables, and labels, take protective measures, such as spreading wet cloth,

around the welding joints.

● Do not use face-down bonding when welding.

Step 9 Install the refrigerant oil heating belt and ground cable for the compressor, install

the cable trough, install the compressor cables, and install the cover.

NO TICE

Ensure that the phase sequence of the compressor input cable is consistent with

that on the compressor label. Otherwise, the compressor may be damaged.

Step 10 Perform a leakage test with nitrogen.

Step 11 After checking that the smart cooling product does not leak, vacuumize the smart

cooling product and fill the refrigerant.

Step 12 Check that the compressor cable phase sequence is correct, power on the unit,

and tap Start on the home screen.

Step 13 Choose Maint > Diagnostic > Enter to check the system pressure and

temperature and ensure the refrigerant is charged with an optimal status. Ensure

that the system is running normally without alarms.

Step 14 Choose Maint > Performance Maint on the home screen of the display module to

access the performance maintenance screen, and clear the runtime of the

compressor.

----End

12.15.2 R410A Refrigerant

CA UTION

Do not use low-quality refrigerant. The relevant party will be liable for any device

damage caused by low-quality refrigerant.

Verify that the refrigerant is authentic in the following ways:
1. Dial the refrigerant vendor's hotline to confirm the refrigerant authenticity.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

179

Содержание FusionCol8000-E24














































































































































































































































































Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E24, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E24

Отзывы:

Похожие инструкции для FusionCol8000-E24

Бренды по названию

Популярные бренды