Huawei ePico3801 Скачать руководство пользователя

Страница: 29 / 75

Power Consumption Specifications

Table 2-10

Power Consumption Specifications of the ePico3801

Item

Specification

The TX power is 100 mW
(20 dBm).

AC/DC power adapter

≤

28W

PoE power supply

≤

30W

The TX power is 250 mW
(24 dBm).

AC/DC power adapter

≤

32W

PoE power supply

≤

35W

Environmental Specifications

Table 2-11

Environmental specifications of the ePico3801

Item

Specification

Temperature

Operating temperature: -5°C to +40°C

Storage temperature:-40°C to +70°C

Relative humidity

Relative humidity of the operating
environment: 5% RH to 95% RH

Relative humidity of the storage
environment: 5% RH to 95% RH

Altitude

-60 m to +4000 m

Air pressure

70 kPa to 106 kPa

2.5 Application Scenarios

The ePico3801 is widely used for indoor coverage in small and medium enterprises (SMEs),
SOHOs, schools, and office buildings and for hot-spot indoor coverage at pubs, airports, stores,
and hotels.

2.5.1 Access Networking Scenarios

The ePico3801 is connected to an enterprise LAN or modem, which connects the ePico3801 to
the public IP network. Then, the public IP network connects the ePico3801 to the AG, and the
AG connects the ePico3801 to the UMTS core network. Through convergence and UMTS traffic
and signaling forwarding performed by the AG, routing towards the UMTS core network is
achieved. The ePico3801 can be connected to the public IP network in LAN access mode or
modem access mode.

2.5.2 Installation Scenarios

If installed in a factory or office building, the ePico3801 does not require a private equipment
room.

ePico3801
User Guide

2 Introduction to the ePico3801

Issue 01 (2009–09–23)

Huawei Proprietary and Confidential

2-15

Содержание ePico3801












































































Результаты поиска

Содержание ePico3801

Отзывы:

Похожие инструкции для ePico3801

Бренды по названию

Популярные бренды

Huawei ePico3801, Руководство пользователя

Результаты поиска

Содержание ePico3801

Отзывы:

Похожие инструкции для ePico3801

Бренды по названию

Популярные бренды