Huawei EDFA0820-D Скачать руководство пользователя страница 40

Страница: 40 / 46

Possible causes and procedures

Possible causes

Procedures

The device receives CATV
signals abnormally.

Check whether the device receives any CATV signals.

The connector of the fiber patch
cord or the input port of the
EDFA is not clean.

Check whether the connector of the fiber patch cord or
the input port of the EDFA is clean using the fiber end-
face inspector.

Hardware is faulty.

Contact Huawei technical support engineers.

3.5.4 The PWR Indicator Is Off

Symptom

The PWR indicator is off.

Possible causes and procedures

Possible causes

Procedures

The power supply is faulty.

Please refer to

3.4.2 Common Power Module Faults

Other hardware is faulty.

Contact Huawei technical support engineers.

3.5.5 The ACT Indicator Is Off

Symptom

The ACT indicator is off.

Possible causes

Hardware is faulty.

Procedure

Contact Huawei technical support engineers.

3.5.6 The LASER Indicator Is Off

Symptom

The LASER indicator is off.

EDFA0820-D
Routine Maintenance Guide

3 Common Troubleshooting

Issue 02 (2018-07-02)

Huawei Proprietary and Confidential

Содержание EDFA0820-D















































Результаты поиска

Содержание EDFA0820-D

Отзывы:

Похожие инструкции для EDFA0820-D

Бренды по названию

Популярные бренды

Huawei EDFA0820-D, Руководство по регулярному техническому обслуживанию

Результаты поиска

Содержание EDFA0820-D

Отзывы:

Похожие инструкции для EDFA0820-D

Бренды по названию

Популярные бренды