Huawei ECC800-Pro Скачать руководство пользователя страница 313

Страница: 313 / 368

Procedure

Step 1 Set smoke sensor parameters.

NO TE

In this example, the smoke sensor is connected to the AI/DI_1 port on the rack environment

unit.

1. Log in to the ECC800-Pro WebUI as an administrator.
2. Choose Monitoring > Cabinet > IT Cabinet n > Cabinet Collector n >

Running Parameters.

3. In AI/DI_1 Port Settings area, set AI/DI_1 sensor to Enable, and click

Submit.

4. Set AI/DI_1 sensor type to Smoke sensor, and click Submit.

Step 2 Check the monitoring functions of smoke sensor.

Table 8-29 Function check

Check Method

Normal Connection Status

Alarm Clearance Method

Simulate a

smoky

environment

under the smoke

sensor.

Smoke sensor status(AI/

DI_1) is displayed on the

active alarm page of the app

or WebUI.

If Smoke sensor type is

Smoke Sensor, power off

and reset the smoke sensor

to clear the alarm.

----End

8.1.7.32 How Can I Set and Add the Smoke Sensor (Connected to the AI/DI

Port on the UIM20A expansion module)?

If a smoke sensor is installed, perform the following steps to configure it.

Prerequisites

One end of the network cable has been stripped, core wires 1, 5, and 8 have been

short-circuited, core wires 6 and 7 have been connected to the cable delivered

with the smoke sensor, and the other end of the network cable has been

connected to the AI/DI port on the UIM20A expansion module.

Context

●

If the sensor is prefabricated, only check its settings.

●

The actual value prevails. Only the method of the parameter settings is

described.

Procedure

Step 1 Set smoke sensor parameters.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

302

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды