Huawei ECC800-Pro Скачать руководство пользователя страница 311 | Manualshive

Страница: 311 / 368

background image

Table 8-26 Function check

Check Method

Normal Connection Status

Alarm Clearance Method

Simulate a

smoky

environment

under the smoke

sensor.

Smoke DI alarm is displayed

on the active alarm page of

the app or WebUI.

● If Smoke sensor type is

Smoke Sensor, power off

and reset the smoke

sensor to clear the alarm.

● If Smoke sensor type is

set to Smoke

Sensor(NC), press the

reset button of the smoke

sensor to clear the alarm.

----End

8.1.7.30 How Can I Set and Add the Smoke Sensor (Connected to the AI/DI

Port on the Skylight Actuator)?

If a smoke sensor is installed, perform the following steps to configure it.

Prerequisites

The smoke sensor has been connected to the AI/DI port on the skylight actuator

using a network cable.
To connect the cable for the smoke sensor, perform the following steps:
Short-circuit core wires 1 and 8 on the other end of the network cable, and

connect the network cable to the cable delivered with the smoke sensor. The

following table describes the cable connection.

Table 8-27 Smoke sensor cable connection

Wire of the Network Cable

Smoke Sensor Cable

Core wire 1 (orange-white), core wire

8 (brown)

GND (black)

Core wire 3 (green-white)

+12 V (red)

Core wire 6 (green)

Normally closed end (yellow)

Core wire 7 (brown-white)

Common end (green)

None (reserved; no connection needed

and to be insulated)

Normally open end (blue)

Context

●

If the sensor is prefabricated, only check its settings.

●

The actual value prevails. Only the method of the parameter settings is

described.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

Copyright © Huawei Technologies Co., Ltd.

300

«
...
309
310
311
312
313
...
»

Содержание ECC800-Pro

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ECC800-Pro

Бренд: Particle Страницы: 6

Бренд: UNITED Страницы: 22

Бренд: Hafele Страницы: 82

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Galaxy Control Systems Страницы: 5

Бренд: Tamas Страницы: 12

Бренд: Panasonic Страницы: 8

Бренд: Yolink Страницы: 23

IntelliCross TouchFree Kit

Бренд: Novax Страницы: 3

Бренд: Daikin Страницы: 19

Бренд: Objective Imaging Страницы: 11

Бренд: Burkert Страницы: 15

DX99N9X1S2N0M2X0D2

Бренд: Banner Страницы: 13

Бренд: Quasar Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды