Huawei ECC800-Pro Скачать руководство пользователя страница 309

Страница: 309 / 368

Figure 8-20 Detecting smoke

(1) Smoke compartment

(2) ALM indicator

----End

8.1.7.29 How Can I Set and Add the Smoke Sensor (Connected to the AI/DI

Port on the ECC800-Pro)?

If a smoke sensor is installed, perform the following steps to configure it.

Prerequisites

●

Connecting Cables to the Smoke Sensor (NC):
The smoke sensor has been connected to the AI/DI port on the ECC800-Pro

collector using a network cable.
Short-circuit core wires 1 and 8 on the other end of the network cable, and

connect the network cable to the cable delivered with the smoke sensor. The

following table describes the cable connection.

Table 8-25 Smoke sensor cable connection

Wire of the Network Cable

Smoke Sensor Cable

Core wire 1 (orange-white), core

wire 8 (brown)

GND (black)

Core wire 3 (green-white)

+12 V (red)

Core wire 6 (green)

Normally closed end (yellow)

Core wire 7 (brown-white)

Common end (green)

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

298

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды